How do you disconnect push fit pipe fittings?

Push fit pipe fittings are designed to make plumbing installations and repairs easier and faster. They work by using an O ring or gasket to create a tight seal between the fitting and the pipe. To disconnect push fit pipe fittings, follow the steps below :

  1. Turn off the water supply : Before disconnecting the fitting, turn off the water supply to prevent water from spraying out of the pipe.

  2. Release the pressure : To release any pressure in the pipes, open a faucet at the lowest point in the system.

  3. Identify the fitting : Locate the push fit pipe fitting that needs to be disconnected.

  4. Mark the pipe : Use a marker to mark the pipe to ensure that the fitting is reinstalled in the same position.

  5. Press the release collar : Locate the release collar on the fitting. The release collar is a ring that is pushed towards the fitting body to release the pipe.

  6. Push the pipe : While pressing the release collar, gently pull the pipe out of the fitting. Wiggle the pipe back and forth if it is difficult to remove.

  7. Inspect the fitting : Inspect the fitting for any damage or wear. Replace the fitting if it is damaged.

  8. Reinstall the fitting : To reinstall the fitting, insert the pipe into the fitting until it reaches the O ring or gasket. Push the fitting and the pipe together until they lock in place.

  9. Check for leaks : Turn on the water supply and check for leaks. Tighten the fitting if necessary.

Disconnecting push fit pipe fittings is a simple process that can be accomplished by pressing the release collar and gently pulling the pipe out of the fitting. Remember to turn off the water supply, release the pressure, and mark the pipe before disconnecting the fitting.

Step by Step Guide to Disconnect Push Fit Pipe Fittings :

  1. Turn off the water supply : Before disconnecting the push fit pipe fitting, you need to turn off the water supply to prevent water from spraying out of the pipe. You can do this by shutting off the main valve.

  2. Release the pressure : Release any pressure in the pipes by opening a faucet at the lowest point in the system.

  3. Identify the fitting : Identify the push fit pipe fitting that needs to be disconnected.

  4. Mark the pipe : Use a marker to mark the pipe to ensure that the fitting is reinstalled in the same position.

  5. Locate the release collar : Locate the release collar on the fitting. The release collar is a plastic ring that is pushed towards the fitting body to release the pipe.

  6. Push the release collar : Push the release collar towards the fitting body while pulling the pipe out of the fitting. Be careful not to damage the fitting or the pipe.

  7. Wiggle the pipe : If the pipe is difficult to remove, wiggle it back and forth while pulling it out of the fitting.

  8. Inspect the fitting : Inspect the fitting for any damage or wear. Replace the fitting if it is damaged.

  9. Reinstall the fitting : To reinstall the push fit pipe fitting, make sure the pipe is clean and free of debris. Insert the pipe into the fitting until it reaches the O ring or gasket. Push the fitting and the pipe together until they lock in place.

  10. Check for leaks : Turn on the water supply and check for leaks. Tighten the fitting if necessary.

Tips for Disconnecting Push Fit Pipe Fittings :

  • Use a pipe cutter to cut the pipe if you are having difficulty removing it from the fitting.
  • Use a deburring tool to remove any burrs or rough edges on the cut end of the pipe.
  • If you are having difficulty pushing the pipe into the fitting, apply a small amount of water or soap to the end of the pipe to lubricate it.
  • If the push fit pipe fitting is stuck, use a pair of pliers to grip the fitting and twist it back and forth while pulling on the pipe.

In conclusion, disconnecting push fit pipe fittings is a simple process that can be accomplished with a few basic tools. Remember to turn off the water supply, release the pressure, and mark the pipe before disconnecting the fitting. Push the release collar towards the fitting body while pulling the pipe out of the fitting, inspect the fitting for any damage or wear, and re install the fitting by pushing the pipe into the fitting until it locks in place.